- Yep, you need a tech 2 tool which is like 20 some hundred dollars to program the remote, but it's quick and they should do it for free. Oh and today i went to the dealer to get some keys cut for my aura and i get out of my car and lock it and the one right beside me locks as well. There's like a billion frequencies and i had the same one as the car beside me sooooo when i left i started it.
- Before you enter the programming sequence for your Saturn vehicle, make sure you have your ignition key, every keyless remote that you would like to program and a jumper wire. Start the pre-programming sequence by entering your car and closing all of the doors behind you. Insert your key into the ignition and leave the key in the 'Off' position.
Step by step guide on how to reprogram an automotive key/door remote for GM Ford and Honda
Difficulty Scale: 1 of 10
Step 1 - GM PASS LOCK RELEARN
- Ignition switch to 'run' position, try to start and let key return to 'run' position
- Approx ten minutes security light will go off
- Turn key 'off' and wait 5 seconds
- Repeat 2 more times for a total of 3 relearns.
- Turn key off, then start it
Step 2 - FORD KEY PADS
2008 SATURN SKY; 4 CYL; 2WD; AUTOMATIC; 37,000 MILES; How do I reprogram the key fob on my 08 Saturn Sky. Have the same problem? Thursday, June 30th, 2011 AT 1:39 PM. KHLOW2008 EXPERT; Here are the procedures. TRANSMITTER PROGRAMMING Invalidate All.
- Enter permanent factory code
- Press the 1/2 button within 5 seconds to enter programming mode
- Within 5 seconds enter new code, doors will lock, unlock to verify code, this erases previous codes. Remotes will also need to be programmed.
Step 3 - FORD KEY PADS/REMOTES
- Insert key, turn ignition off-to-on eight times in succession, ending with key in on position doors will lock, unlock to verify in programming mode
- Press any button on new remote, doors will lock, unlock to verify
- Do the previous step with the second remote, doors will lock unlock to verify.
- Turn ignition switch off. Doors will again lock, unlock to verify.
Step 4 - BLAZER T-CASE SELF DIAGNOSTIC
- Turn ignition switch 'ON' for at least 6 seconds.
- Locate DLC (diagnostic connector) near right side of steering column.
- Install jumper wire from pin #13 (orange wire, labels are small but they are on connector, use flashlight) to ground.
- Turn the key on, engine off. Observe shift select buttons. If they all blink once at the same time there are no trouble codes.
- Otherwise the light will blink (codes are 1-4 flashes) with a 3 second delay between codes if there are more than 1.
- Run the codes if any are present repair as needed.
Step 5 - HONDA SLIDING DOOR RE-HOME
- Erase the sliding door trouble codes by removing the # 13 (7.5) fuse from the passenger's under-dash fuse box for 10 seconds.
- Then put the fuse back in.
- Turn off the main door switch; make sure that the ignition switch is off.
- Manually open the sliding door and make sure it's fully open.
- Turn the ignition switch on, then turn on the door switch.
- Push and hold the CLOSE side of the dashboard door switch for that door until the door is fully closed.
- Try the door operation with the dashboard door switch, the remote and the door handles.
Helpful Information
A remote can perform many functions such as lock and unlock car doors, start the engine, roll up windows and much more. When a key fob is lost or becomes out of sync with the car receiver module, reprogramming is necessary.
Common Problems
- Key fob remote battery goes dead and needs replacement
- Moister damage
IMPORTANT – READ ME
Your vehicle requires that remotes must be programmed by an automotive locksmith or dealership. There is no way to program themwithout the proper diagnostic tools.
Please hand these instructions to your locksmith or automotive professional.
Dear automotive professional,
If the vehicle does not accept the remote during your standard programming procedure, please try these steps.
Instead of holding down LOCK & UNLOCK for 15 seconds. Press and hold LOCK & UNLOCK for 6 seconds, release BOTH buttons and
tap ONLY the UNLOCK button.
If that doesn’t work please make sure that the vehicle’s battery has a full 12v charge.
It is always best to program remotes with a Jump Pack connected to the vehicles battery.
These vehicles only have a maximum of 4 remotes so please make sure that the vehicle is not maxed out on remotes.
Please make sure that the vehicle does not any sort of aftermarket alarm or remote start. These will need to be disabled before new remotes can be programmed.
Saturn Aura Key Fob Programming
We test all remotes prior to shipping but sometimes batteries can get drained while in transit from other packages pressing on the
buttons for extended periods of time. If the remotes still do not program please have the customer contact us so that we can better assist them.